Hello everyone,<\/p>\n
We launch the monthly news on the evolution of the community within fuel-it.
\nThis article arrives with a new category on our blog, the category “community”.<\/p>\n
We’ll give you a summary of our articles of the month, the evolution of our community on social networks, as well as articles about us on the web if we are lucky to have some (and we’re lucky) this month :) )<\/p>\n<\/div><\/div><\/div><\/div><\/div>
Human Resources level<\/strong><\/h2>\n<\/div><\/div><\/div>The most important event this month is the arrival of Antoine. Antoine who comes to reinforce the team in the communication.<\/p>\n
This month, Antoine focused on developing the Facebook community. We are now 100 to follow Fuel-it’s activities on social networks. Antoine has also learned to use 3D printers to manufacture our sensors, he now masters very well.<\/p>\n<\/div><\/div><\/div>
![\"Fuel-it](\"https:\/\/fuel-it.io\/wp-content\/uploads\/2017\/06\/blog-photo-antoine.jpg\" "\\"blog_cover_photo_antoine\\"")
<\/span><\/div><\/div><\/div><\/div><\/div>Advances on the connected sensor<\/strong><\/h2>\n<\/div><\/div><\/div>Many improvements took place on the sensor this month:<\/p>\n
\n- Evolution of the screw pitch<\/li>\n
- Starting up the ILS<\/li>\n
- Design modification<\/li>\n<\/ul>\n
The most visible one is of course the evolution of the screw thread. We went from a single screw pitch to a triple screw pitch. This evolution allows the connected sensor to be adapted to any type of tank without any adapter.<\/p>\n
The reed switch (ILS) is finally up and running. The sensor remains in deep sleep, consumes only a few micro-amperes and does not transmit any frames until it is activated via the ILS.<\/p>\n
The design has been revised, mainly to facilitate 3D printing. The top of the sensor has been smoothed and an edge reduced to reduce the amount of media needed for printing.<\/p>\n
The most important event this month is the arrival of Antoine. Antoine who comes to reinforce the team in the communication.<\/p>\n
This month, Antoine focused on developing the Facebook community. We are now 100 to follow Fuel-it’s activities on social networks. Antoine has also learned to use 3D printers to manufacture our sensors, he now masters very well.<\/p>\n<\/div><\/div><\/div>
<\/span><\/div><\/div><\/div><\/div><\/div>Advances on the connected sensor<\/strong><\/h2>\n<\/div><\/div><\/div>Many improvements took place on the sensor this month:<\/p>\n
\n- Evolution of the screw pitch<\/li>\n
- Starting up the ILS<\/li>\n
- Design modification<\/li>\n<\/ul>\n
The most visible one is of course the evolution of the screw thread. We went from a single screw pitch to a triple screw pitch. This evolution allows the connected sensor to be adapted to any type of tank without any adapter.<\/p>\n
The reed switch (ILS) is finally up and running. The sensor remains in deep sleep, consumes only a few micro-amperes and does not transmit any frames until it is activated via the ILS.<\/p>\n
The design has been revised, mainly to facilitate 3D printing. The top of the sensor has been smoothed and an edge reduced to reduce the amount of media needed for printing.<\/p>\n
Many improvements took place on the sensor this month:<\/p>\n
- \n
- Evolution of the screw pitch<\/li>\n
- Starting up the ILS<\/li>\n
- Design modification<\/li>\n<\/ul>\n
The most visible one is of course the evolution of the screw thread. We went from a single screw pitch to a triple screw pitch. This evolution allows the connected sensor to be adapted to any type of tank without any adapter.<\/p>\n
The reed switch (ILS) is finally up and running. The sensor remains in deep sleep, consumes only a few micro-amperes and does not transmit any frames until it is activated via the ILS.<\/p>\n
The design has been revised, mainly to facilitate 3D printing. The top of the sensor has been smoothed and an edge reduced to reduce the amount of media needed for printing.<\/p>\n
![\"Evolution](\"https:\/\/fuel-it.io\/wp-content\/uploads\/2017\/06\/blog_communaute_juin.jpg\" "\\"blog_communaute_juin\\"")
<\/span><\/div>